Seyeon FW1170 Manual de usuario Pagina 13

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 48
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 12
Technical Specifications
1173MM Network Camera
Video Encoding MJPEG / H.264 (simultaneous dual stream)
[Protocol]
HTTP, RTP/RTSP, Multicast, 3GPP, TCP/IP, ARP, ICMP, Telnet, Ftp, PPPoE,
SMTP, DHCP, NTP, uPNP, and ETC
[SDK]
Open HTTP API / ActiveX for live cast with audio & PTZ
System
Integration
Features
[Service]
Image upload / notification service / special service for POS integration
Video channels Analog 1 Input channels & 1 Output Channel (loop through).
Installation and
maintenance
Configuration: installation wizard, HTTP, telnet and console.
Upgrade firmware: HTTP, telnet & ftp
Compression
H.264 & MJPEG : 6 levels (low compression / highest / high / normal / low /
lowest)
Misc.
OSD (On-Screen Display) / Time-stamp on video
Transmit serial input data with video
Support NTP server
Quick Time & VLC media player compatible for live view
Resolution
SXGA - 1280x1024
VGA - 640x480
CIF – 320x240
QCIF – 160x112
System hardware 32bit RISC CPU / Embedded Linux / 128MByte SDRAM / 8MByte Flash
Live Casting
Streaming 1 video channels with full duplex live audio
Up to max. 30fps@ 4CIF (KB) , 15fps@SXGA when simplex
Power
Power Supply - SMPS 12V (800mA) [AC100~240V, 50/60Hz]
Power Consumption - DC12Volt, 500mA
Audio
Encoding
8 bit PCM, Sampling rates 8KHz, Mono Audio Approvals MIC,FCC, CE, RoHS
Audio channels 1ch audio-in & 1ch audio-out
Dimension /
Weight
84 (W) x 110 (D) x 35 (H) (in mm)
0.214Kg without Power Supply
PTZ support
Built-in PTZ device protocol with more than 30 different PTZ protocols from
Pelco, Vicon, Kalatel, Sony, Panasonic, Canon, Honeywell, etc
External
Interface
1ch video inputs & 1 composite output (75 ohm/Hi-Z)
10/100-Base-T Ethernet (auto-sensing)
1 photo-coupled or 1 digital inputs (NC/NO selectable), 1 relay outputs
1 audio input / 1 audio output
2 serial ports (COM: RS-232, AUX: RS-232 or RS-485)
UART support
Console, By-pass command to control UART device
X10 device command to control device over power line, Modem Support
( ISDN, PSTN and GSM )
Working
Environment
Temperature : 32~122 F (0~50
O
C)
Humidity : 20~80% RH
Bandwidth
Management
Frame rate control / Bandwidth control / CBR / VBR
Image sensor
1/3(5:4) Micron Progressive Scan CMOS
Active imager size : 4.6mm(H) x 3.7mm(V), 5.9mm diagonal
Active pixels : 1280H x 1024V
Pixel size : 3.6 x 3.6μm
Color filter array RGB Bayer pattern
Shutter type Electronic rolling shutter (ERS)
Responsivity 1.0 V/lux-sec (550nm)
SNR MAX 44dB
A
ccessory
POE module
Sold separately
* All specifications are subject to change without prior notice.
Alarm
Management
(for 1 analog
channels)
[ Trigger Condition ]
Video loss / Video recovered / Motion detection (144 area) /
1ch alarm inputs / Boot finished / Serial input / Schedule
[ Alarm Service ]
Image holding service (Max 15.5MByte pre-post alarm buffer)
Image upload service through E-mail / FTP (support pre & post)
Notification service through TCP / UDP / HTTP / 1 alarm outputs
Lens
Shipped without lens
CS mount
No Iris Control
For Mega Pixel Sensor
Security
Channel based user password protection for live-cast, PTZ, alarm output
and audio
LENSE(MANUAL)
No Iris Control
Image
Setting
Dynamic IP
Support
Dynamic IP service using www.ipcctvdns.com
Minimum
illumination
2-10000 lux, F1.8
Software
(default
Web interface)
Live-cast, PTZ control, search through Web browser
(Minimum PC requirement - XP, 2000, Vista / IE 6.x or later )
Software
(FW-Manager 3.xx)
Supports 16, 25, 36, 64, 128, 256ch ( 9ch freeware available)
Full-featured PC NVR with matrix functionality
( Minimum PC requirement - XP, 2000 / Pentium IV 1.6GHz or above /
256MByte RAM or above / 64MByte video memory or above )
Power Over
Ethernet
IEEE 802.3af Built-in wireless(optional)
13
Vista de pagina 12
1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 47 48

Comentarios a estos manuales

Sin comentarios